• Proceedings of the 06th annual symposium 2000 (Pre Text) 

  Hettiarachchi, P [Conference-Full-text]
• Preparation and properties of starch xanthide encased powdered natural rubber 

  Amarasinghe, ADUS; Subramaniam, K; Maduwage, S [Conference-Full-text]

  Starch xanthide encased powdered natural rubber was produced by oxidatively co- precipitating the mixture of starch xanthate solution and natural rubber field latex under vigorous stirring. The resulting finely divided wet ...
• Prediction of compressive strength of concrete 

  Nanayakkara, SMA [Conference-Full-text]

  This report presents a method of predicting the compressive strength of concrete. The approach is based on experimental investigation of compressive strength development of four mix proportions with three different brands ...
• Performance analysis of pedestal fans an experimental investigation 

  Sugathapala, AGT; Somarathne, PBI [Conference-Full-text]

  Performances of pedestal fans were analysed through experimental measurements of the induced flow field (velocity distribution) and the power consumption by two different types of fans. A test rig was constructed to ...
• Passive concepts for improvement of thermal and visual comfort in houses in Sri Lanka 

  Jayawardane, AI; Jayasinghe, MTR; Attalage, RA [Conference-Full-text]

  One of the primary requirements of houses constructed in hot humid climatic conditions such as those prevailing in Sri Lanka is that those should be thermally comfortable for the occupants throughout the day and around the ...
• Optical characterstics of carbon based semiconductors 

  Munindradasa, DAI; Amaratunga, GAJ [Conference-Full-text]

  The photoluminescence (PL) in a-C:H:N was measured using a 2.4leV Ar ion laser line for varying N content. The PL results show a lowering of the PL peak energy and a spectral line width broadening as the N content in the ...
• Knowledge based software for loading and stability of ships 

  Wimalsiri, WK [Conference-Full-text]

  Loading and Stability calculations of ships became a more and more complicated and time consuming process as the ship sizes and design complexity increased. Accurate and efficient methods of evaluating and analysing stability ...
• Internally, stabilized earth retaining systems with discarded tyres 

  Kulathilaka, SAS; Nawagamuwa, UP [Conference-Full-text]

  Internally stabilized earth retaining systems became popular and came into extensive usage over the last two decades due to the many advantages inherited in them. Different forms of internally stabilized earth retaining ...
• Influence of linings on stress and deformation in rock around tunnels 

  Puswewala, UGA; Gunatilaka, IRP; Hapuarachchi, CL; Nandasena, RM [Conference-Full-text]

  Stress distribution and deformation in rock around lined tunnel openings subjected to internal pressure are investigated by using plane strain finite element analysis. Two typical tunnel cross- sections, in the forms of ...
• Improving the efficiency of electro discharge machining by dual voltage excitation 

  Jayasinghe, JAKS [Conference-Full-text]

  An Electrical Discharge Machine (EDM) is a vital machine used in manufacture of tools and dies. Its operation is based on discharge of an electrical current across the tool and the work-piece. Due to limitations of the ...
• Evaluation of cost of unserved energy in Sri Lanka 

  Wijayatunga, PDC; Fernando, WJLS [Conference-Full-text]

  Quantitative reliability evaluation is an important aspect of power system planning and operation. The indices produced in these applications are utilised in a wide range of management decisions throughout a utility. One ...
• Energy conservation in industry: motor drives 

  Wijayatunga, PDC; Daranagama, DAU [Conference-Full-text]

  A significant proportion of electrical energy generated is utilised in industrial motor drives in addition to it being used for electric lighting and heating. Also, oversized and under-utilised motors in the industrial ...
• Development and evaluation of the aesthetics of structural form 

  Kulasuriya, C; Dias, WPS; Hettiarachchi, MTP [Conference-Full-text]

  This Paper demonstrates that the aesthetic concepts of engineering design do not just arise; but that they are derived from various models of aesthetics. It also presents various Proportioning Systems and their application ...
• Designing fuzzy logic damping controllers for large practical power systems 

  Peiris, HJC [Conference-Full-text]

  A methodology for designing fuzzy logic damping controllers for large practical power systems is presented in this paper. The proposed approach uses (i) the Prony Signal & Transfer Function Identification Technique to ...
• Design of yagi array receiving antennas using genetic optimization 

  Jayasinghe, JAKS [Conference-Full-text]

  YAGI array is a very popular antenna for VHF/UHF applications due to its simple construction. It is extensively used in television and FM radio reception. However, design of YAGI arrays to meet a given set of specifications ...
• Design of continuous prismatic prestressed concrete spine beams with variable prestressing forces 

  Ranasinghe, WMDN; Jayasinghe, MTR [Conference-Full-text]

  Design of continuous prismatic prestressed concrete continuous spine beams is a complex task, primarily due to the secondary moments that occur as a result of the prestressing effects. In prestressed concrete members, it ...
• Design & construction of an energy-efficient furnace for melting non-ferrous alloys in the local foundry industry 

  Tittagala, SR; Navarathna, NPNM [Conference-Full-text]

  A study has been carried out on the types of construction and factors affecting efficiency of metal melting furnaces currently used in the non-ferrous foundry sector with the objective of developing an oil-fired furnace ...
• Chemical treatment of timber, a novel method 

  Fernando, MARV [Conference-Full-text]

  Dwindling resources of quality timber made manufacturers to look for alternatives. Species such as Rubber -"Hevea brasiliensis" were found to be good alternatives once treated against "Borer" attack. While expensive ...
• Cashew nut shell liquid based polymer resin for making air- drying varnishes 

  Subramaniam, K; Fernando, S [Conference-Full-text]

  As cashew nut shell liquid (CNSL) is a natural source of phenols, attempts are made in this work to prepare a synthetic polymer resin from the liquid, by treating it with formaldehyde. The polymer resin thus prepared is ...
• Application of mebrane separation processes to the Sri Lankan industry 

  Amarasinghe, BMWPK; De Silva, IMBM [Conference-Full-text]

  Membranes and membrane based separation techniques have developed rapidly over the last two decades with a considerable technical and commercial impact. The technology is now widely used for a range of applications including ...

View more